Throttle body fitted

[Eoghan]

Id say 20 mins or so would do it...

[luckyfrank]

Id say 20 mins or so would do it...

cheers

[Damok]

Leave it 40mins to an hour. .

[luckyfrank]

b**** !!!!! The idle has returned to normal but im having the same problems as before im getting a knocking noise from the throttle body

I had to use the throttle position sensor of the old one in the 2nd hand body i got as the inlet pipe to the sensor was broken thats obvioulsy whats bolloxed, i also checked the maf sensor and it's caked in oil which i say isnt helping

Total pain in the b**** and a waste of money ill have to look for a new thorttle body the f*** in england will be a nightmare to deal with to try get my money back the GF signed for the goods after i told her not to as i wanted to check for damage they wont give me my money back

[P.D.87RWD]

Ah F**k lad that's hard luck hopefully you will have some luck getting money back but it will be hard once signed for...Best of luck and hope you get it sortted...

[Evelyn]

Who diagnosed a trottle body?? Are you sure its not a manifold leaking problem??

[luckyfrank]

Who diagnosed a trottle body?? Are you sure its not a manifold leaking problem??

Robbie in tdp said thats what it was he said the clicking noise im hearing was the motor in the throttle body being unable to reset thus giving me bad idle

[Damok]

Its hardly a vaccum leak or a blocked pipe? Have you tried swapping out the MAF sensor. . Take a video of the rev gauge to try show us how its idleing

[Evelyn]

Is the flap in the trottle body so?? Just make sure who ever fitted the trottle body did it right any gasket leak will cause the idle to be bad aswell that has to be sealed tight.

[luckyfrank]

Its hardly a vaccum leak or a blocked pipe? Have you tried swapping out the MAF sensor. . Take a video of the rev gauge to try show us how its idleing

I'll take a video of it 2moro if im home early enough, cant clean the maf sensor as it would mess with the mapping of the car

[nivek]

just ajust the throttle position sensor on the side of the TB .
leave the car runnig and open the two screws slightly and rotate the sensor a little bit.

Impossible to get to those screws though, you'd need the car jacked as there facing the road and even than woud be hard to do with all the stuff in the way

no there not that bad to get at . i did it on mine aboot a month ago.

[luckyfrank]

just ajust the throttle position sensor on the side of the TB .
leave the car runnig and open the two screws slightly and rotate the sensor a little bit.

Impossible to get to those screws though, you'd need the car jacked as there facing the road and even than woud be hard to do with all the stuff in the way

no there not that bad to get at . i did it on mine aboot a month ago.

what did you do exactly ? did you leave the engine running while you done it, how much did you turn it by

[luckyfrank]

Im loading a few vids of the throttle body knocking and the bad idleing, hope someone can help when they see should be ready in 20 mins

[Damok]

Im loading a few vids of the throttle body knocking and the bad idleing, hope someone can help when they see should be ready in 20 mins

Will try help, mines ideling funny as well keeps dropping to 550RPM so i have a new MAF sensor coming
the next few days i hope it sorts it.

[luckyfrank]

ok first one is the vid of bad idleing

http://www.youtube.com/watch?v=wlY6aN10Fv0

And this one is the thorttle knocking

http://www.youtube.com/watch?v=LypFWA-B12I

So any idea's guys, i think the knocking is the thorttle position sensor from the old throttle body that i had to put into the new one but im not 100% sure