Image Please bare with us while we are carrying out some much needed maintenance to the forum. New look coming soon!

Do's & dont of painting headlights!!!!!!

Section for all helpful how-to's related to Altezzas
Forum rules
This forum is now a closed section, it is purely for reference on how to do work on your Altezza. If you have a query please post in the relative section.
User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Do's & dont of painting headlights!!!!!!

Postby Evelyn » Tue Sep 23, 2008 5:28 pm

Might pluck up the courage at the wkend & do this (was going to change them but due to finances, this is what I am doing)

First question does the bumber have to come off?
Has anyone done this, any tips??

User avatar
Noel
Moderator
Posts: 3726
Joined: Sat Mar 03, 2007 6:18 pm
Location: oldville

Postby Noel » Tue Sep 23, 2008 5:32 pm

Theres a vid on youtube ... :D

back in a minute :wink:

ok watch this ... http://uk.youtube.com/watch?v=P-q0SVALfus

it's a vid for installing Halo lights but he paints them while they're open ...

also remember he is in the states so the temperature on the oven is in fahrenheit

good luck
Last edited by Noel on Tue Sep 23, 2008 5:36 pm, edited 1 time in total.

User avatar
Richie_c
Altezza Guru
Posts: 1744
Joined: Tue Feb 19, 2008 1:07 pm
Location: Everywhere
Contact:

Postby Richie_c » Tue Sep 23, 2008 5:35 pm

Some of the lads will tell you that the bumper doesnt have to come off, I had to take mine off though.
When youre taking them out be very careful as their clips that hold the unit in place after all screws/nuts are removed, I managed to break one of them when doing it.
When putting the units in the oven be careful not to put them too close to the elements as they will melt
I put them in at just under gas mark 1 for about 15 minutes. May need longer may not
Use screwdrivers to seperate the glass from the housing and then just pull the housing away very smoothly
Be careful when seperating the unit not to get glue on the inside of the unit
After that sand down the insides of the housing
Prime the housing
Paint them. Will need 2/3 layers of paint
Put them back together when fully dried
Put them back in the oven at the same temperature
When you take it back out push the light smoothly down on a flat surface - I used a table with a towel on it and rolled the light from side to side to seal it back up
Use vicegrips to hold it together to make sure it seals correctly after you've used as much (wo)man power as possible

Think thats pretty much it, I hope I havent left anything out
300 rwhp thanks to
Image

User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Postby Evelyn » Tue Sep 23, 2008 5:49 pm

Ya I have seen the video Noel, but was just wondering had anyone anymore advise, but I think Richie has covered it...

User avatar
Flex
Altezza Guru
Posts: 634
Joined: Thu Jun 05, 2008 9:21 pm
Location: Trinidad and Tobago

Postby Flex » Tue Sep 23, 2008 5:51 pm

(HSI) Handle Speed Intelligently
Image

User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Postby Evelyn » Tue Sep 23, 2008 5:56 pm



Ya that what I have printed off, so hopefully it should go to plan...hopefully

User avatar
Dan
Site Admin
Posts: 3792
Joined: Sat Feb 24, 2007 3:43 pm
Location: Dublin

Postby Dan » Tue Sep 23, 2008 5:56 pm

i didnt need to remove the bumper, there is only 2 screws behind the wheel arch plastic cover that are tricky to get to and be careful with the plastic clip on the bottom of the light

User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Postby Evelyn » Tue Sep 23, 2008 8:14 pm

1 other thing will the heat resistant matt black I have left over from the brake calipers do the job?

User avatar
Dan
Site Admin
Posts: 3792
Joined: Sat Feb 24, 2007 3:43 pm
Location: Dublin

Postby Dan » Tue Sep 23, 2008 8:38 pm

no need for heat resistant paint, may not bond properly to the plastic, make sure you give them a few coats of grey primer first, sand them down and a few coats of matt black. i smashed one of my inserts to bits when sanding it, had to superglue it back together! you couldnt tell it had been smashed by the time i was finished with it!

User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Postby Evelyn » Tue Sep 23, 2008 8:41 pm

I know its a stupid question I presuming the reason there silver in the first place has got to do with projection of light, does making them black affect the light?

User avatar
xnickx
New Zealand Rep
Posts: 805
Joined: Sat Apr 07, 2007 11:26 pm
Location: Auckland, NZ
Contact:

Postby xnickx » Tue Sep 23, 2008 10:33 pm

Not on the housing, dont paint the 2 chrome circles that the light reflects from.

Quick tip:
- 100degrees C preheat for 5 mins
- Stick the lights in for 5 mins
- Pull the lights out and put toothpicks on the little tabs that hold the clear plastic onto the housing
- Stick the lights back in and oven and pull them out every 2 mins and slowly peel them apart

Did mine exactly with that way (and a few others) and have yet (touch wood) have any deformation on the tabs etc etc

User avatar
Sub-Z
Tezza Fanatic!
Posts: 339
Joined: Tue Jul 08, 2008 2:35 am
Location: Wexford
Contact:

Postby Sub-Z » Tue Sep 23, 2008 11:56 pm

Goodluck wit the venture eve should make ur headlights look very good indeed painting them.
Only God Can Judge Me
Image

User avatar
Evelyn
Moderator
Posts: 6062
Joined: Mon Sep 10, 2007 9:06 pm
Location: Galway
Contact:

Postby Evelyn » Wed Sep 24, 2008 9:34 am

Ya totally with ye now...Just spotted Sub-z car & I can see where the silver reflective is left :oops: bit slow god love me but I get there in the end :lol:. I am used of looking at headlights where the actually glass in tinted not the insert....

User avatar
Ms_beams
Trc Off
Posts: 184
Joined: Tue Nov 27, 2007 11:34 am
Location: Limerick
Contact:

Postby Ms_beams » Wed Sep 24, 2008 10:25 am

Get onto mark....i'm sure he'd have a good few tips about this :wink:
Mark Moloney x (1984-2012)

Image

User avatar
d2carazy
Clare rep
Posts: 2738
Joined: Thu Apr 24, 2008 9:49 am
Location: Ennis, Clare, Ireland
Contact:

Postby d2carazy » Wed Sep 24, 2008 12:02 pm

best of luck with it it sounds like a lot of work


Return to “How-Tos”

Who is online

Users browsing this forum: No registered users and 1 guest

cron