Image Please bare with us while we are carrying out some much needed maintenance to the forum. New look coming soon!

Minty.Fresh BN Sports Altezza

Once you've introduced yourself why not throw up a few pictures of your car or a project thread?
User avatar
RS Tom-Hundred
Tezza Fanatic!
Posts: 450
Joined: Fri Nov 28, 2014 3:31 pm
Location: Cambridgeshire

Re: Minty.Fresh BN Sports Altezza

Postby RS Tom-Hundred » Wed Dec 03, 2014 12:55 pm

Looking good and cant wait to see this all done and back on the road! :)

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Wed Dec 03, 2014 4:11 pm

The bastard clutch finally turned up!

Image

Pressed the old pilot bearing out using a slice of bread, and hammered the new one in. Began bolting on the pressure plate.

Image

One of the bolts just wasnt threading in for some reason though. So I took it out, and tried a longer bolt. Threaded it in.... And just pulled it right out by hand again..... f*** bollocks!!!

Just my luck, I got a used flywheel with a stripped thread!

Image

Couldnt really check it properly before, since it only became apparent once i started tightening the pressure plate on. Spoke to Garage D, and they apologised and offered to fix it. So thats being sent off to them today.

That pissed me right off, and i felt like finishing up for the night. But regardless, decided to connect the boost controller solenoid while the engine is out from the car.

Pulled the pipe that goes from the compressor outlet to the wastegate actuator.

Image

Dug out the instructions. Yes, I do read instructions!.

Image

Used what I had lying around, and connected everything up. Mounted the solenoid at the back of the turbo intake.

Image

With another pipe getting reference boost from the intake manifold, with a t-piece that will connect to the in-car boost gauge.

Image
Image

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Tue Dec 09, 2014 10:39 am

Intake s@3! is slowly arriving.

Image

Cheap fluids for the 'flush'

Image

And then I had nothing to do, I was bored, so I decided to sort out the wiring loom. relocate the ECU inside and tuck all wires inside bar the wiring for the lights, horn, washer bottle etc...

So out comes the dash

Image

For reference, this is what was in the bay originally

Image

Loom feeds though the bulkhead though the pass and drivers side. So need to unplug it from both junction boxes in the footwells

Image

And pull all the s@3! out

Image

This was the picture I was once I pulled everything out. Originally i only planned to move the ecu inside, leaving all the relay boxes in the pay as they were originally. But after seeing how clean this looked, I decided to go full retard.

Image

Loom layed out on the floor

Image

Stripped and radiator fan relay wiring chopped out

Image

Then separate the loom a bit and were left with something like this.

Image

Lights and ECU separated. Then proceeded to sort the drivers side and continue removing unused wires in the process. Airbag, old Altezza ecu wiring (trc etc..) So ended up with something like this. Arrows where it will go through the bulkhead.

Image

Next, unbolted the dash mount. Unbolted the heater stuff and pulled everything back. Removed the aircon condenser hoses. Lifted the center bit of the heater up and fed the loom through there.

Image

Guided the loom in places where the pedals wont come into contact with it, and stuck it down so it wouldnt move. Drivers side plugged back in and all done.

Image

Pass side required a bit more tidying up

Image

=

Fed the ecu loom to the airbag location. And tucked everything up and away. Taped the relay/fuse box up as a temp measure.

Image

Just to see what it looks like with the dash

Image

The ecu will live here

Image

And this is what we ended up with in the engine bay. Still untidy since the wires arent organised and are just all over the place just now. But they wont be visible at all once the engine is in. Mega clean imho. Some will need to be extended slightly to reach the lights. But not a big issue at all.

Image

And with the aircon pipes removed, it opened up this for the JZ engine loom to be fed though.

Image

All the leftovers....

Image
Image

User avatar
choopz
Altezza Guru
Posts: 1531
Joined: Wed Nov 04, 2009 11:28 pm
Location: Aruba
Contact:

Re: Minty.Fresh BN Sports Altezza

Postby choopz » Tue Dec 09, 2014 8:38 pm

Superb job bro!!
Loving it :wink:
Image
Light travels faster than sound. This is why some people appear bright until you hear them speak.

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Thu Dec 11, 2014 12:18 pm

Been tidying up the wiring in the engine bay. Kinda hard in this cold weather, especially with a weak ass soldering iron. Finished extending the wiring on the pass side. Whole loom wrapped up is about 10mm in diameter. Will run along the chassis leg out of sight.

Image

And a lifestyler pic of the 'show cars'

Image
Image

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Fri Dec 12, 2014 11:14 am

Pretty cold here last few days. Made a little enclosure haha

Image

All wiring extended, just the the stuff inside the car left to do. And the remainder of the engine wiring (gearbox speed, reverse...etc)

Image

Mint came round last night with some goodies from Japan. KTS pulleys, cause my alternator one was bent to s@3!.

Image
Image

Trd Shane
Tezza Fanatic!
Posts: 232
Joined: Mon Dec 02, 2013 10:44 pm
Location: Dublin

Re: Minty.Fresh BN Sports Altezza

Postby Trd Shane » Fri Dec 12, 2014 9:12 pm

peter0991 wrote:Pretty cold here last few days. Made a little enclosure haha

Image

All wiring extended, just the the stuff inside the car left to do. And the remainder of the engine wiring (gearbox speed, reverse...etc)

Image

Mint came round last night with some goodies from Japan. KTS pulleys, cause my alternator one was bent to s@3!.

Image


Shinnyyyyyy :shock:
"If it can't be fixed with a hammer it's an electrical problem"

Pingu Is200
Noob!
Posts: 19
Joined: Thu Jul 18, 2013 11:09 am
Location: United Kingdom

Re: Minty.Fresh BN Sports Altezza

Postby Pingu Is200 » Sat Dec 13, 2014 4:19 pm

your mad doing the conversion this time of year but atleast youll be shreading rubber again inn the summer.

and with abit of luck less problms then Nickys had.
Charged-Is200

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Tue Dec 16, 2014 9:18 am

Note to self: Dont do conversions outside during winter again. Its cold!

Image

Made the airbag lid 'push-to-open'

Image

Image

Stuck the interior back in

Image

Ended up leaving the relay box in the passenger footwell incase I ever need to get to it. Dont want to be pulling the dash apart to change a fuse

Image

Then finished the intercooler mounting.

Image

Image

All bolted up and rigid as f***. Should be ok

Image

Then pulled the lights out, chopped them a little bit more to prevent any fretting

Image

And sealed them up

Image
Image

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Thu Dec 18, 2014 12:21 pm

Went on a mission last night.

Flywheel arrived

Image

And fitted

Image

Bolted the box up. Struggled a bit with the clutch release bearing. The ACT clutch came with a weird release bearing spring. Ended up using oem w58 spring.

Image

Then I thought, f*** it, might as well drop it in. When in Rome...

Image

IS200 propshaft, straight fit. Perfect!

Image

Clutch lines connected and bled. Not keen on fuel line location. Will be relocated when I run braided lines.

Image

Shifter location is spot on. But the angle of the mk3 supra shifter is s@3!. Got a gangster lean. Will be chopped and modified to be straight at some point.

Image

Didnt get into the house until late. So will continue tonight.
Image

User avatar
peter0991
Altezza Guru
Posts: 580
Joined: Wed Jun 22, 2011 10:29 am
Location: Aberdeen, Scotland

Re: Minty.Fresh BN Sports Altezza

Postby peter0991 » Mon Dec 22, 2014 2:27 pm

Work night out on Friday....Whole weekend wasted to s@3!...

Still managed to squeeze in a few hours of car stuff last night.

All piping hooked up. Idles like a beast, neighbors love that s@3!!

Image

Image

Still a few minor issues with bleeding the coolant system. But I'll get there. The rad is lower that the hose, so a bit of an airlock present. But there is hot air coming from the heater.

Image

Hooked up the rest of the wiring. Alternator is now charging. Reverse beeps and hopefully the speedo works as well. Havent tested that out yet. Just need to tidy s@3! up now.

Image

The cleanest engine bay ive ever had

Image
Image

User avatar
choopz
Altezza Guru
Posts: 1531
Joined: Wed Nov 04, 2009 11:28 pm
Location: Aruba
Contact:

Re: Minty.Fresh BN Sports Altezza

Postby choopz » Mon Dec 22, 2014 11:15 pm

Man that is one heck of a job bro, congrats :wink:
Image
Light travels faster than sound. This is why some people appear bright until you hear them speak.

User avatar
mlcoolj
Altezza Guru
Posts: 1740
Joined: Tue Oct 20, 2009 8:14 pm

Re: Minty.Fresh BN Sports Altezza

Postby mlcoolj » Tue Dec 23, 2014 7:55 am

getting there!
Image

User avatar
RS Tom-Hundred
Tezza Fanatic!
Posts: 450
Joined: Fri Nov 28, 2014 3:31 pm
Location: Cambridgeshire

Re: Minty.Fresh BN Sports Altezza

Postby RS Tom-Hundred » Tue Dec 23, 2014 8:50 am

Nice one! :D

Pingu Is200
Noob!
Posts: 19
Joined: Thu Jul 18, 2013 11:09 am
Location: United Kingdom

Re: Minty.Fresh BN Sports Altezza

Postby Pingu Is200 » Tue Jan 06, 2015 10:56 pm

just need to rip up Driftland now its done
Charged-Is200


Return to “Member's Cars / Projects”

Who is online

Users browsing this forum: No registered users and 1 guest