ImageGreetings! Welcome to Tezzaworld website, unfortunately you are a few years late to the show as nearly everyone has been and gone, there is still lots of useful archived material to read through, not many active users unfortunately, but that’s the way it goes, hopefully you are not too disappointed...

3S-GE-Beams Blacktop forged low comp block

Have a part for sale? Put it in here
JZZ30
Trc On!
Posts: 45
Joined: Sun Aug 18, 2013 7:08 pm

3S-GE-Beams Blacktop forged low comp block

Postby JZZ30 » Mon May 08, 2017 8:49 am

Good day folks.

Due to a change of plans I am am skipping on forced induction looking to swap my forged beams black top block for a standard block.
The only reason is that I now want to compete in a national touring car series where non stock forced induction is prohibited.

My block as available for a swap:

Precision bored out to 86.5mm
Honed to 0.1mm cylinder to wall clearance
deck skimmed
Main Bearings - ACL Race Bearings
Thrust Bearings - ACL Race Bearings
Lower connection Rod Bearings - ACL Race Bearings

Eagle forged connecting rods (from 3S-GTE)

Wiseco 86.5mm forged pistons from 2JZ-GTE machined to fit oil squirters and larger 3S-GE valves and diff. valve angle.

Can also supply a 1.8mm Apexi metal cylinder head gasket.

Final comp. will be at approx. 9.6:1 (standard head gasket) or 8.4:1 (with the 1.8mm Apexi head gasket)

Build block totaled at about £1'400

Looking for a clean low mileage standard block (complete assembly - crankshaft, rods, pistons) as partial exchange.

Price £800 (+£140 for Apexi head gasket)

Or

Cash sale.

Price £1'100 (+£140 for Apexi head gasket)

Would also consider an aftermarket exhaust header (HKS, Toda or similar) as par ex.

I could also supply a used Greddy cast manifold, a freshly balanced Garrett GT2871RS turbocharger, new 850ccm Injectors and 3" pipe and silencers to build a full 3" exhaust with vband clamps (downpipe already tig welded).

If you are interested please don't hesitate to contact me for questions or further details

JZZ30
Trc On!
Posts: 45
Joined: Sun Aug 18, 2013 7:08 pm

Re: 3S-GE-Beams Blacktop forged low comp block

Postby JZZ30 » Thu May 11, 2017 5:19 pm

Would also remove custom pistons and eagle connecting rods and sell separately:

4 Pcs. 86.5mm custom milled 2JZ-gte Wiseco piston incl. pin and Piston Rings for 0.10mm wall clearance
They will fit stock or 3s-gte connecting rods

Price £380

Set of eagle 3s-gte forged H-beam connecting rods to fit stock or forged 3S-ge pistons or the above

Price £300

Apexi metal head gasket 1.8mm to reduce compression (to 9.6:1 with stock internals or 8.4:1 with the setup above).

Price £130

JZZ30
Trc On!
Posts: 45
Joined: Sun Aug 18, 2013 7:08 pm

Re: 3S-GE-Beams Blacktop forged low comp block

Postby JZZ30 » Sat May 20, 2017 4:53 pm

Pics to be found in my Driftworks for sale thread:

https://www.driftworks.com/forum/thread ... ck.255693/

THE BOM3
Trc On!
Posts: 51
Joined: Sun Jun 21, 2009 12:03 pm

Re: 3S-GE-Beams Blacktop forged low comp block

Postby THE BOM3 » Fri Aug 11, 2017 6:26 pm

This still available?? Sent you a pm


Return to “Parts for sale”

Who is online

Users browsing this forum: No registered users and 2 guests

cron